Q: Pcmcia Lucent Tech. ... Help Plz.

Postby Zool » Fri Feb 01, 2008 5:14 pm

Привет всем,
Помогите, мож. кто сталкивался, не могу установить, вернее, настроить pcmcia orinoco silver.

(insmod wavelan_cs - загружает модуль нормально , вручную, т.е. и pcmcia и карта работают
нормально нр как настроить, чтоб стартанул интерфейс у карты не могу понять :(.)

Помогите плиз, уже 3 день ничего не могу вразумительного сделать :(

Благодарю за помощь.

мои действия:

1. установил поддержку pcmcia (pkg -i /.../pakages/pcmcia)
установилось без проблем.

2. настроил rc_pcmcia setup

3. получил конфиги, вот такие:

/etc/pcmcia/config
#################################
device "wavelan_cs"
class "network" module "wavelan_cs"

card "Lucent Technologies WaveLAN Adapter"
version "Lucent Technologies", "WaveLAN/IEEE", "Version 01.01"
manfid 0x0156, 0x0002
bind "wavelan_cs"

# Include configuration files for add-on drivers

source ./*.conf

# Include local configuration settings

source ./config.opts
#################################

/etc/pcmcia/config.opts
#################################
# System resources available for PCMCIA devices

include port 0x100-0x4ff, port 0x800-0x8ff, port 0xc00-0xcff
include memory 0xc0000-0xfffff
include memory 0xa0000000-0xa0ffffff, memory 0x60000000-0x60ffffff

# Options for WaveLAN/IEEE driver (AccessPoint mode)...
module "wavelan_cs" opts "station_name=FeeSCO_PC"
#################################

/etc/pcmcia/network.opts
#################################
case "$ADDRESS" in
*,*,*,*)
# Transceiver selection, for some cards -- see 'man ifport'
IF_PORT=""
# Use BOOTP? [y/n]
BOOTP="n"
# Use DHCP? [y/n]
DHCP="n"
# Host's IP address, netmask, network address, broadcast address
IPADDR="10.1.100.90"
NETMASK="255.255.255.0"
NETWORK="10.1.100.0"
BROADCAST="10.1.100.255"
# Gateway address for static routing
GATEWAY="10.1.100.1"
# Things to add to /etc/resolv.conf for this interface
DOMAIN=""
SEARCH=""
DNS_1=""
DNS_2=""
DNS_3=""
# NFS mounts, should be listed in /etc/fstab
MOUNTS=""
# For IPX interfaces, the frame type and network number
IPX_FRAME=""
IPX_NETNUM=""
# Extra stuff to do after setting up the interface
start_fn () { return; }
# Extra stuff to do before shutting down the interface
stop_fn () { return; }
;;
esac


/etc/pcmcia/wireless.opts
#################################################
case "$ADDRESS" in

# NOTE : Remove the following four lines to activate the samples below ...

# Here is an example of scheme matching
# Activate with "cardctl scheme essidany"

# Pick up any Access Point, should work on most 802.11 cards
essidany,*,*,*)
INFO="Any ESSID"
ESSID="any"
;;

# Here are a few examples with a few Wireless LANs supported...
# The matching is done on the first 3 bytes of the MAC address

# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
*,*,*,00:60:1D:*|*,*,*,00:02:2D:*)
INFO="Wavelan IEEE example (Lucent default settings)"
ESSID="Wavelan Network"
MODE="Managed"
# RATE="auto"
KEY="s:secu1"
# To set all four keys, use :
# KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
# For the RG 1000 Residential Gateway: The ESSID is the identifier on
# the unit, and the default key is the last 5 digits of the same.
# ESSID="084d70"
# KEY="s:84d70"
;;


# Old Lucent Wavelan
*,*,*,08:00:0E:*)
INFO="Wavelan example (Lucent default settings)"
NWID="0100"
MODE="Ad-Hoc"
FREQ="2.425G"
KEY="off"
;;

# Generic example (decribe all possible settings)
*,*,*,*)
INFO="Fill with your own settings..."
# ESSID (extended network name) : My Network, any
ESSID=""
# NWID/Domain (cell identifier) : 89AB, 100, off
NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE=""
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL=""
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
SENS=""
# Bit rate : auto, 1M, 11M
RATE=""
# Encryption key : 4567-89AB-CD, s:password
KEY=""
# RTS threshold : off, 500
RTS=""
# Fragmentation threshold : off, 1000
FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
esac
User avatar
Zool
Newbie
 
Posts: 1
Joined: Fri Feb 01, 2008 2:37 pm

Return to Russkij - Russian

Who is online

Users browsing this forum: No registered users and 1 guest

cron